Alguien sabe algo de esto, lo habeis probado, funciona???? (yo no puedo probarlo que no tengo el coche en casa) Os dejo la direccion para que podais leerlo mas claro: http://www.ultimate-bmw.com/bmw_knowledgebase/bmw_obd_and_fault_codes.htm BMW OBD (On Board Diagnostics) and Fault Codes Last edited/updated on 8/31/04 There are two engine management systems used on 92-99 BMW's, which differ in significant ways. They are: OBD I used on 1992-1995 models OBD II used on 1996-1999 models (note: some 99 models are E46 BMWs) If you have a BMW car with OBD II engine management you will need to purchase a fault code or scan tool reader in order to utilize the BMW codes below. If you have a BMW with an OBD I engine mangament system, then you can read the fault codes from your BMW as follows. 1. Turn the ignition key on and fully depress the accelerator five times within a five second period. 2. After this, the check engine light will go through a sequence of: staying on for five seconds, go off, stay on for 2.5 seconds, go off for 2.5 seconds. 3. After this the fault code will flash. The BMW fault code is a four digit number, however your BMW may display more than one fault code. In this case each code will be seperated by a 2.5 second pause. After all codes have been displayed there will be a .5 second flash and the light will stay off. The table below lists some of the fault codes that could be displayed. BMW OBD Fault Codes Code Reason 1211 DME Control module may be bad. 1215 Mass air flow sensor or wiring to the sensor may be faulty 1216 Throttle Potentiometer wiring may be faulty 1221 Oxygen Sensor #1 might be faulty 1222 Oxygen Sensor mixture ratio out of bounds (rich/lean) 1223 Coolant temperature sensor might be faulty. Check wiring 1224 Air Temperature Sensor might be faulty. Check wiring 1225 Knock Sensor #1 Check knock sensor and wiring 1226 Knock Sensor #2 Check knock sensor and wiring 1231 Battery voltage monitor. Check battery voltage and charging 1234 Speedometer. Check wiring to instrument cluster 1237 AC compressor cutoff. Test control module inputs from AC system 1242 AC compressor signal. Test control module inputs from AC system 1243 Crankshaft Position sensor. Check wiring from sensor to control module 1244 Camshaft Position sensor. Test camshaft position sensor and wiring 1245 Electronic transmission control intervention 1247 Ignition monitor. Check secondary voltage to coils 1251 Fuel Injector #1 1252 Fuel Injector #2 1253 Fuel Injector #3 1254 Fuel Injector #4 1255 Fuel Injector #5 1256 Fuel Injector #6 1261 Fuel Pump Control. Check relay and wiring 1262 Idle speed control. Check air control valve 1263 Evaporative system (fuel tank) 1264 Oxygen sensor heater. Check heater and relay 1265 Check engine lamp. 1266 VANOS. Check VANOS solenoid 1267 Air pump relay. Check relay and wiring. 1271 Ignition Coil #1 1272 Ignition Coil #2 1273 Ignition Coil #3 1274 Ignition Coil #4 1275 Ignition Coil #5 1276 Ignition Coil #6 1281 DME Control module memory supply 1282 Fault code memory. Control module may be faulty 1283 Fuel Injector output stage. Control module may be faulty 1286 Knock Control test pulse. Control module may be faulty 1000 Light remains off. All fault codes have been displayed 1444 No more faults
Informacion mas detallada en esta pagina... http://www.pelicanparts.com/BMW/techarticles/JF-Tech/E30_E36_On_Board_Diagnostics .htm